Tag Archives: Hurricane Florence

Bimini and Dodger, More Varnish and Sanding

by

Bimini:

Just prior to Hurricane Florence last year, I made an error on leaving my solar panels and bimini in place.  Well, sort of an error.  I knew that the windage would be high and the bimini was mounted under the solar panels, and the posts holding the solar up went THROUGH the bimini.  I also realized how damaged and aged the bimini was.

Leaving it up was a recipe for disaster if things got bad.  Taking it down was a recipe for disaster because of age.

I left it up.  We “lost a solar panel” off the top.  The wind ripped it loose and dropped it, fortunately, on the deck of the boat where it remained until I returned after the hurricane in October last year.  I easily repaired the small amount of damage and observed the bimini wasn’t in great shape, but survive.  It had a couple of small tears in it.

This time, as Dorian approached, I removed EVERYTHING from the deck.  We pulled Adventure into the marina, deep inside up near the containment bulkhead and positioned her inside a shallow slip at high tide, so we settled into the mud when the King Tide fell off.

Dorian hit with a whisper of winds (40 knots perhaps on shore here), the eye wall missing us by a good 30-35 miles.  Adventure came through fine.  The bimini however, as well as the dodger have seen better days.  So, I never reinstalled it.

About a month ago, I ran into a canvas guy, David from “Custom Canvas” out of New Bern.  He gave us a quote for lowering the bimini, creating a new bimini and dodger (no enclosure this time) and adding a few extra pieces.

The steel was lowered at one visit.  Another visit resulted in several more measurements, some grab rails and the bows over the top of the bimini top on which to mount the solar panels.

David was here a few days ago, installed the bimini, and subsequently, I installed the solar panels in a preliminary location – which, might move slightly back soon.  I am not sure I like them exactly where they are, and I want extra room for the boom to swing by the top of the bimini.  I’ll work that out later.

Dodger:

He is returning today, to bring the dodger, which for the uninitiated is the part that covers the front of the cockpit, and “dodges” the spray and waves that can wash over the front of the boat at times.  We had the top of the dodger lowered as well, so that I can now re-learn climbing in and out of the companionway getting whacked in the head.  But, the point was to allow JoAnne to actually see over the TOP of the dodger now.

Before, when driving the boat, she could never get a clear view in front of the boat.  She had to duck down and look through the dodger window, or stand on her tiptoes to see above it, while leaning over to see past a sail.  Not fun for her, I assure you.

We dropped it down about 5-6 inches and had her stand behind the wheel.  When she was happy with the height, we stopped cutting.  I’m concerned I’ll have a few knots on my head, climbing in and out in the next few days once installed, but eventually, like Pavlov’s Dogs, I’ll learn.

Sand and Varnish:

Over the course of the past months, I’ve spent roughly 30 hours sanding wood, washing it, and varnishing.  I have about 90% of the teak done – on the top of the boat.  I haven’t touched the rub rails, or the plaques on the boat topsides yet.  And I haven’t done any varnishing to the aft deck (the whole aft of the boat is a raised, teak platform which covers a large storage compartment, containing our propane tanks and extra “stuff” we don’t want to leave on the deck, like pumps, parts for the emergency tiller, etc)

That deck will likely take a third of a quart of varnish alone for a single coat.  I’ll likely finish that first coat today or tomorrow.  After it hardens, I’ll be hitting the wood all the way around the top of the boat, once over, a complete boat wash, taping and varnishing the second coat.  I plan, if time and weather permits, to get some of the deck paint done and to fix a couple of leaks so the outside of the boat should be ready in less than two weeks.

Given the heat of the day, and humidity, I’ve tried to apply varnish in the right time of day, temps and humidity, but I’m here to tell you, this is an impossible task unless the boat is moved inside a building in a controlled environment.  So… it’s called “going with the flow” (of varnish, which flows off things, down tape, drips everywhere and is constantly being cleaned up).

After all that work, the boat looks amazing though, and in the end, it makes JoAnne smile at how pretty the boat is.  I makes my muscles ache when I see it….. But, I still like the varnished wood.

I plan to get about five coats on if I can, with fine sanding in between, and then do “touch up” coats after a few months to keep it looking nice.  It’s less work to do that, than to let it get down to bare wood.

Someone asked me the other day about sanding the boat and then varnishing it, then sanding again.  They have an all-Clorox-Boat, so I explained that it is supposed to take down the bubbles or ‘nibs’, and raised rough spots, and give the next coat something on which to cling.  They were impressed I knew so much about varnish (HAHAHA, little do they know, I just had to look it up to explain it to them!)

Side Note: Our friend Jason has also been sanding and sanding and vanishing and washing and sanding and varnishing as well.  I believe he completed his last coat last night.  The boat rails look amazing.

Storage Locker and Provisions: 

We have a storage locker.  I pay for it a year in advance.  It’s due in November I think, so I’ll be going over to write them a check for another yet, and going through my locker to pull out a few things and bring to the boat, as well as remove a few more things from the boat we won’t need.  I want ‘parts’ that I can use to repair things, even if makeshift if necessary, and I want heavy things off the boat I can’t use while under way (certain electrical tools).  We have little A/C power available except for the generator during cruising, and I’ll reserve that for the water maker most of the time, but will bring my battery drill, a saw and my small electronic tools, and the engine tools.

Also I have a sail in storage I need to bring back, and we need our water, diesel and gas cans back on the boat.  Need a way to carry extra water if we can’t make it or catch rainwater, diesel because I HATE docking at fuel docks and gas for the genny.

In a few days we will need to being picking up food to provision the boat.  We’re going to get a month’s worth of things, mostly long term storage items like canned foods, along with perhaps a week (whatever JoAnne decides can work for us) of fresh items and we will refill things as we go down the coast this time, instead of having six months worth of stuff on the boat this time.  Before we hope to Bahamas we’ll do a big food, beer and soda run (yes, we drink soda!) and stock up on things that are expensive in the Islands.  (Toilet paper, paper towels, etc)

We don’t use many paper towels (instead we buy cheap white cloths from the hardware store and reuse them) and tend to use the marina heads when we stop in them instead of the boat, but offshore… well, anyway….

JoAnne had her medical check up on the 9th of September.  We’ll have to work something out for one in December, and I think we’ll be calling back to her doctors here in NC to get advice on that subject when we get closer to the time.

My last obstacle is the Borg-Warner Velvet Drive Transmission.  Over the past couple of years, it’s given me fits.  Seemingly it stops “working” and then “works”.  We have determined that its simply a lack of transmission fluid, but where it is going, we’re unsure.  It’s not in the bilge, and I don’t think it is mixed in with the few drops of oil in the catch pan under the engine.

Someone suggested it is going out under pressure in the heat exchanger perhaps, once the engine reaches temperature.  I tend to agree since I’m not finding leaks anywhere else.  If so, then the solution will be to remove and replace the heat exchanger that is connected to the transmission.  I’ve identified the unit, and the hoses, but am not sure it there is a way to “test” for leaks at this point.  Meantime, I need to keep extra transmission fluid on the boat.

I’m sure I’ve missed something. I usually do.  But, that’s ok, I’ll figure it out when I come to it.

In the mean time, I rarely if ever do this, but I want to remind folks that I’ve written some books and I’d love it if some of you would take the time to read and review the books on Amazon.  I’ll drop the links at the bottom of this page.  One book is a couple of years old, and is about “Survival and Communications” and is a primer for people who don’t know much about radios and radio communications.  Call it a “Prepper Book” if you like.  It’s in Digital Format ONLY and I won’t be doing it in hard copy because it’s simply too expensive.  And if you’re a Prepper, then you know you’re NOT going to grab 200 of your favorite books and stuff them in your bug out bag.  You need to KNOW the information, knowledge is power. Don’t carry a book, carry your brain around with the information inside.

The other book is a SF Adventure/Thriller, “Aftermath’s Children” set in the not-too-distant future, and you can read the description online at Amazon.  That book is in both digital and hard copy formats.  You can find all three versions of the books at the link below.

https://www.amazon.com/Rick-Donaldson/e/B00Q514LD0

I invite you to buy it, read it, review it and if you get the hard copy, and we pass by, I’ll sign it for you.  The second book in the series is being completed soon.   Please, drop me a line at Adventure.Rick.JoAnne@gmail.com or r.daledonaldson@gmail.com if you buy a copy!  Thanks!!!

 

SeaPro Reverse Osmosis Watermaker

by

Well over a year ago I was doing research on water makers – reverse osmosis water makers specifically.

I wanted a modular system, and had found one, but the price was about 5-6 thousand dollars.

I also researched building my own, and found I didn’t really have the time and money to slap-dash something together, only to find parts wouldn’t fit and I couldn’t make it work.

Then, one day I came across SeaWaterPro and decided to contact them.  My first contact was with Mindy at SeaWater Pro.

I asked her a lot of questions in both email and messenger.  Eventually, I was convinced for the cost of the system (1/3 the cost of the RainMan system at the time) I’d go with it for a test.

The system was modular, and I could build it into the boat in a piecemeal fashion, because as everyone knows, boats are limited on storage space, especially cruising vessels like our own.

As luck would have it, I purchased the kit over a year ago, and things began to happen.  Engine issues, hurricane Florence and JoAnne was diagnosed with a return of cancer.  In September last year we prepped the boat for Florence, and headed for Florida, storing the water-maker and most of our important things, expecting that Florence would make landfall as a Category four, here in Cape Fear Region.

She didn’t.  Fortunately. (Read more here: Hurricane Florence)

In the end, we returned to Colorado, then back here to the ship to prep for winter, as we’d spend it there.  Time got away from us.  Six months in Colorado in the winter time, staying with my wonderful son, Nick.  I know we probably stressed him out though we tried very hard to stay out of his hair the whole time.

Eventually, in April we returned.

I started devising ways to install the watermaker in the boat.  Over the course of the next few weeks, I ended up making the decision to remove the 30 gallon stainless steel tank sitting under the settee, and replace it with the watermaker.  The system would JUST fit in there.

Video of device in operation.

In fact, I could with relative ease, plumb the hoses and tubes I needed for input, output, overboard discharge, and electrical wiring under the seat.

Throughout it all, I kept in contact with Mike, the designer of the system, and he responded rapidly with both answers to my questions, and advice on various issues I had.  Being an engineer myself in another life, it wasn’t difficult to understand the system, how it worked, but some things were rather vague for me – because I wasn’t familiar with the system yet.

Installation took me about two weeks, along with another delay of several days due to heat in the boat (the temperatures and humidity got to me).

When I finally plumbed everything I did I pressure test and it leak like a sieve.   This was not the system’s fault, but mine. I had forgotten to use teflon tape on all the junctions and found I’d only applied it on some of the junctions.  Disassembly was easy because I installed it so I could remove various parts, especially the pre-filters, for changing and cleaning.

Mike actually ended up shipping me some new parts due to the length of time from when I had originally ordered the system to present.  He upgraded several items at no cost to me, which I sincerely appreciated.

A 1 hp electric motor and high pressure pump instead of his original design went into the boat.

I had to go buy a few extra feet of plastic hose to route the output, and I had to change a few fittings to get the right hoses in the right places.

In the end, I fit all the parts except the lift pump, and strainer under the settee.  The lift pump and strainer are in the forward compartment under the Vee Berth, right next to the intake through hull.  The saline overboard discharge also runs forward to an existing through hull above the water line.

There were no holes cut into the boat to do the job. I spent about 10 hours doing the install from scratch.

The second test was done under generator power.  I wanted to run the machine off the generator, as I will do on anchor.  I need to do a longer test to determine exactly how much gas it takes to fill my 60 gallon tank, but that is for another day.

I fired up the lift pump, let the system fill with water, checked for discharge water, and then fired up the pressure pump.  Next you turn a pin valve to increase the pressure.  At about 475-500 PSI the RO filter because to produce water.

The first bit (roughly an hour’s worth of run) must be run off to ensure the preservatives are removed from the RO filter.  The device is adjusted to be a steady 21gpm (on my system) and when that part was finished, I began running fresh water to a bucket, and checking the Total Dissolved Solids (TDS) meter.  It showed a consistent 78-88 reading.  Checking with Mike once more, I found that because we are in the ICW and brackish water, we will run that low.

Pure sea water should run around 200 ppm, and FDA standards state that anything under 650 ppm is safe to drink.

When finished, I ran fresh water (from the outside faucet) through the (provided) carbon filter system to 1) remove chlorine, and 2) to flush the RO filter to prevent bacterial growth.

I have run the system twice in the past two weeks with very good results, as well as having plumbed the fresh water directly to another, already existing host to the 60 gallon tank down in the bilge.

I will include pictures later – probably tomorrow, as I’m just too tired to figure out where I put them all right now and upload them!

Over all, I give this system a 4.6 out of 5 stars….

Customer Service: 5.0

Documentation: 4.5

Equipment: 5.0

Functionality: 5.0

Difficulty of Assembly: 3.5

 

Documentation is mostly images, and probably works for most people, but the images do not necessarily show the exact parts in MY kit.

As to difficulty of assembly, the system is NOT hard to put together and make function.  The hard part is really based on your particular needs, space availability and your own technical ability.  While *I* can assemble nearly anything, including radio systems from scratch, and many mechanical items and devices, I also can read schematics and engineering documents.  Not everyone has these abilities, or would have to work harder to accomplish the same thing I did.  It might take longer.

But, Mike and Mindy have provided EXCEPTIONAL Customer service, responding instantly in some cases to emails, and in enough detail to help me figure out my immediate problems.

My final email to Mike was “Ok, it’s all installed and working.  Any further advice to give?”

Mike responded with, “Yes, take your boat to the Bahamas !! “

Now that Dorian has gone through here, and I’m back in my regular slip, it’s time to run the machine again, make some water and do a few more tests, but at this point, I’m extremely happy with the system.

 

Hurricane Florence

by

Back in September, we had to deal with two life threatening conditions.

The first was a possible Category 4 hurricane (Florence) headed straight for us.

The second was JoAnne’s CA-125 numbers rising.  The CA-125 is a particular cancer antigen they use to determine if there are ovarian tumors growing in her body.  The previous June we noted the numbers had begun to increase.  I think it was late August or early September we had another test performed (it’s a blood test).  The numbers were trending upward.

When we start prepping for the hurricane I doubled-checked our insurance, then removed sails, stowed things, removed important-to-us items, stored things in a storage locker on shore, packed the car and prepared to run.  The night before or the morning of our departure JoAnne received a message from the doctors telling her she needed to come back to Colorado and begin chemo within a few weeks.  Sooner if possible.

We had a PET scan done here in the North Carolina area, and it was determined she indeed had two areas of concern.  One, the one that frightened us the most was a nodule on her left lung on the upper lobe.  The second was a small area that lit up the PET scan, between liver and kidneys.  The lump on her lung was about 1 cm in size.  Significant in that it seemed to be growing rapidly.

We departed on Wednesday morning, with no particular destination.  She called her brother, Paul, down in Tampa Bay area and asked if we could visit for a time during the hurricane and he was more than happy to see us.  So, we headed east and south along the pre-staged hurricane evacuation routes;  there was no turning back once we got out of town.  We had to leave.

We basically had said good bye to our home, Adventure, unsure if we would ever see her intact again.  We figured insurance would help us replace her, or something similar if it came down to that.  But, we have no allusions about such things.  Insurance companies are notorious for NOT paying out on such claim, even with full replacement insurance like we have.  (Note that after being hit in Cobbs Marina by a power boater, while we were docked, we no longer carry just liability insurance.)

The trip south was uneventful.  We arrived. visited with Paul and Cathy, and waited with bated breath as we watched the weather applications on our computers and tablets.  The forecast Cat 4 never happened.  Florence did, however hit at a category 1 and destroyed several marinas to the north of our marina.  We lost a few pieces of the marina (and there is still some damage to this day).  Our own boat suffered minor damage (I could not easily remove the bimini as it has solar panels over the top of it, and I didn’t have enough time.

I had double and triple lined the boat to the pilings and dock, extra fenders and strapped the dock box down to the dock.  It didn’t move and was fine.  Adventure exploded a fender or two, stretched some lines and we got a couple tears in the old bimini.  Minor damage considering some people lost their boats north of us.

We tried to come back… but, roads were out, blocked, bridges were washed out, floods were everywhere and getting back to the marina would have proved problematic with a lack of fuel in the area.

So, onward to Colorado it was.  We saw her doctors, and set up appointments and a chemo schedule.  Finally, we heard people were getting back to Southport, and we had a three week down time before chemo began.  We hightailed it back to Adventure to clean up, repair the damage we could and prep the boat for the long winter of being away from her.

We simply left the boat in “hurricane prep” mode, and I dumped water tanks, and ensure nothing would freeze inside (the weather here rarely gets to freezing and when it does, doesn’t stay low enough for long enough to freeze the water).  With the boat cleaned and ready for winter, we secured her once more and drove the 2000 miles back to Colorado for the fifth trip since June (For anyone keeping track, that’s 10,000 miles in three months, not counting the side trips, and the hop down to Florida, which was roughly another 1600 added in there.)

JoAnne began the chemo in November.  Her chemo would be different this time.  On “Day One” she’d have all the medicines to prevent nausea, plus two chemicals to fight cancer, one was carboplatium and the other gemzar (and I don’t know if I am spelling the two correctly, I’ll fix that later).  Then on “Day Eight”, a dose of gemzar only.

Unfortunately, things began to go wrong.  She had a tooth infection, and wound up having an extraction, and going on antibiotics, thus preventing the Day 8 chemo session.  Instead three weeks later, the session and count down began again.

Day one of the second chemo session went well.  Her blood counts however, did not do well.  Again the day eight session was cancelled.

Each “session” was three weeks apart.  By this time it had been several weeks.  Session three was supposed to go as a Day One chemo infusion, then Day eight would be gemzar followed by Neulasta.  (Neulasta is a chemical they give to kick your bone marrow into high gear to produce white blood cells, and because they were so low, she really needed to get that shot).

Unfortunately, her numbers were so bad, her platelet count was extremely low, red and white cells very low, that it was dangerous for her to be out in public even.  So, they gave her the Neulasta shot, which is actually administered by a tiny robot module stuck to her arm.  It is loaded, armed and placed, then sticks a person with a small needle, to inject the drug 27 hours after the chemo is completed.  So, we have to monitor the device for beeps, lights and infusion.  When it is completed it was my job to remove the robot.

Her blood cell numbers began to look better, but her platelet count continued to spiral downward and would not recover.  We were very concerned.

Platelets, for those who are not well versed in medicine are required for clotting your blood.  So a small cut can bleed profusely, and a larger would could become fatal in moments.  You need to get the platelets back up to a normal number.

We watched the numbers, as she had tests weekly now, so another drive to the hospital, 45 miles round trip sometimes twice per week, we were at the hospital.

On Session Number Four, things start to appear normal.  We went in and her infusion went well.  She did not receive her Neulasta shot yet, as they wished to do the Day Eight Gemzar infusion.  She did get red blood cells.  We did that eight days later, on a Wednesday.  On Thursday we went in for blood work and she wound up receiving platelets as those numbers were still extremely low.  They gave her two units and then checked.  Then gave her two more.

Earlier that morning she had noticed a small blemish on her face.  It had gotten larger.  Then we noticed numerous small, red dots, resembling measles on her arms and legs.  We showed the nurses who then became very concerned.

At five PM, when we should have been out the door on the way home, her doctor ordered her admitted to the hospital.  She was “Neutropenic“.  This is a condition that results in low blood cell counts.  Her platelets were practically missing, and a hematologist was called in.

She was put on bed confinement because if she fell or was bruised in any way, should could hemorrhage.  The lack of white cells may have resulted in sepsis and could have killed her.  She was in danger.

Four days in the hospital later, they had given her some drug to prevent her body from killing off the blood cells they were giving her.  Apparently, her “Super Power” is killing foreign matter inside her own body.  Except cancer.  Her immune system was killing off the platelets they were giving her.  They had to give her red cells and platelets once they stopped the body from killing it off.

In a couple of days she was feeling better, color had returned, the spots were gone and she was ready to go home.

The Gemzar was the culprit.  They stopped giving that to her altogether, and stuck with the carboplatium.

Session Five and Session Six went without a hitch, other than lowered blood cell counts, and receiving the Neulasta shot on time 27 hours after each chemo session.

Three weeks to the day after the last chemo, like our regular clock-work schedule, we visited the hospital for a blood draw.  Fourty minutes later, we were in the PET scan area.  The numbers were back in 20 minutes.  All great.  Everything back to normal.  Except her red blood cells.  We think she is a bit anemic from all of the chemicals and she’s working to fix this with diet, supplements, and so on.  Tomorrow, on Friday, we’d get the PET scan results.

On Friday… we saw the doctor himself.  He was stern.  He didn’t smile.

Then he said, “Well, the PET scan results came back.  We see absolutely no sign of the cancer.  The nodule on your lung is just gone.  The other area isn’t light up.  We DID see some cells around your lung, but, they are not lighting up as if they are cancer.  It looks very good.”

JoAnne and I high-fived.

Wednesday the following week we were packed and were headed out.  First stop was going to be Omaha area, to visit our son Jeremy, who had moved up there and was working.  The car was completely packed and we sneaked out to avoid waking Nick, who had graciously allowed us to stay there for the whole medical adventure.

We left the key inside, went out the garage, secured the door with the electronic system and got in the car.

I put the key in and …. absolutely nothing happened. The car was dead.

We went ahead and got some assistance from the guys, and jumped the car.  Left jumpers on for 20 minutes, and the car started right up.

We drove to Nebraska without killing the car once.  That night we stayed with friends, and the car was fine.  Started up a couple of different times.  Next day we left for Missouri, pass through all the flooded areas, but no car problems.  Checking the car that night when we arrived in Richmond, MO, I found the battery voltages were not at a normal 13.8 after running all day.

I assumed the battery had a bad cell.  I went to Walmart because, as it turns out, some engineer is sitting there getting kickbacks on battery changes in the Dodge Journey.  The battery is NOT under the hood.  It’s not in the trunk.  It’s NOT in the back seat.  It’s under the left, front fender, kind of inside the engine compartment, but to get it, you must remove the wheel, the shroud covering the inside of the fender and then reach WAY up inside to unbolt the battery holder and cables!

Ok… 4.5 hours later at Walmart, the next issue happened.  All of the mechanics except one young kid, had walked off the job leaving my car sitting on the lift, tire off, and battery not looked at.  I, needless to say, complained.

At the end of it all, I personally reinstalled the wheel, taught the kid how to drop his lift, and made sure to Quality Control check his battery installation (because, he didn’t tighten the cables, and didn’t install the bracket to hold the battery down… which might have turn the car into a dangerous missile…..)

I went in to pay for the battery, and the lady at the counter apologized and said “No charge today, Sir, have a good day”.  Just like that.  Free battery?

Cool.

Unfortunately, nothing in life is free.

On Wednesday two days ago, we left Asheville, NC en route for Southport North Carolina, about a six hour drive, give or take.

Everything went very well, except the construction, the crazy drivers and accidents scattered across the region.  JoAnne routed us down and off some of the freeways to avoid accidents.  Somewhere around 501 near Myrtle Beach and a couple of miles before the turn to highway 17, the car began making horrible noises.

Then a “battery light” came on.

Uh oh….

I pulled into a random parking lot.  I grabbed my multimeter which I am going to start carrying around on my belt like a TRUE Nerd from now on, and measured the out put of the alternator.

11.5 volts DC.  Hmm… that’s not normal.  Should be 14.6vdc or so.  Yeah, alternator is NOT charging.  Also some ‘grindy’ noise was coming from the engine.  I listened carefully, and decided it was either an idler wheel, or the tensioner, along with probably the alternator failing.

With the battery at under optium voltage, and after discovering that it would cost 200 bucks just to tow the car around the corner, and have it “diagnosed” (not fixed, just tested), I thanked the lady I’d spoken too and said, “We’re going to try to make it to the marina.  It’s only 52 miles….”

We killed all the power inside, anything charging inside was removed, radio killed, and I illegally ignored my turn signals and avoided stepping on the brakes.

This battery was brand new, and free.  I was going to drive it into the dirt.

And we did.

We arrived a few moments after 5 PM, an hour later than we thought.  At the corner of Fish Factory road and Long Beach Road, I again broke the law.  The light was red.  But, the car was freaking out.  Weird lights on the dash were coming on.  Beeps and buzzes from the dashboard I’d never heard before met our ears.  I made an illegal left turn against a red traffic light.  Of course, there were no cars, and no traffic as the bridge is still closed…. I then, for the third time that day, broke the law.

I went 10 miles an hour over the speed limit.

The car died as I backed into an open space in the lot.

The last bit of momentum took us to the curb.  The car died.  We were home.

That evening I came down, checked the boat, batteries and put the bed together.

Next morning I called the place that had worked on the car last June on the alternator (see, wasn’t the FIRST time we’d had issues). They have the car now, it was towed there yesterday afternoon at 2pm.

He called me three times this morning.

Diagnosis:

  1. Alternator shot, but under a lifetime warranty.
  2. Tensioner wheel is failing, bearings coming out

A new alternator is on order and will be installed Monday morning, along with a new tension wheel and mechanism (probably the spring).

Should have the car back by sometime Monday afternoon.  The cost will likely be 300 bucks, give or take a bit.

(That’s all labor, and perhaps a bit for the parts).

I will NOT be surprised if the brand new battery isn’t shot too.  We’ll find out soon enough.

 

Today is Friday, 5 April 2019.

Nothing in life is set in stone.  Not even those “Death and Taxes” people talk about.  You might avoid both if you’re smart, careful and even, at times, courageous.

One thing in life is certain though… if you don’t try, you can not do.  JoAnne is a tough chick.  She’s a lucky lady and she’s extremely courageous. She is my super hero.  Used to be my Dad was my “hero”.  But, after 40+ years with her, I’ve seen her face death with a smile and overcome it.  I’ve seen her pick up a margarita a few hours after chemo and say “Why not have a little fun? I deserve a margarita!”

I’ve watched her cry quietly over this awful disease. Not for herself but for, the perhaps “missed chances” at things.

I watched her face light up when she holds our newest grandchild, Lincoln, and hug the other grands, and the great-grand daughter.

I have spend sleepless nights myself worrying about her, caring for her, getting her things, bringing her coffee in bed in the mornings and just being there to hold her when she wants me to.

Life changes, but you can either accept things as they are, or you can make your own plans and make your wishes come true.

Cruising life isn’t always about pretty anchorages, great sailing days, and seeing dolphins.  Yes, those things happen.  But, so many other bloggers and video bloggers show you all the “good stuff”.  No one shows you, or tells you how much work it is to get ready for a hurricane, hoping it misses you by a long distance, and how much worry it causes you when you can’t be there to “protect your ship”.

We live our lives now around this boat and each other.  It’s not always positive.  Broken cars, engines, plumbing, leaks, hard rains, strong winds and sometimes broken facilities where you’re visiting, poor service at places (See Walmart above, there’s way more to that story than I actually told you) and even things like “uncontrolled dogs” that some cruisers bring ashore all work to dissuade a person from continuing.

We’ve been LUCKY on a lot of issues.  We’ve also probably paid out a LOT more money than we had to at times.

But, I don’t think either of us would trade this life for a sedate house on a hill in Colorado again.

The best thing?  Coming “Home” to “Welcome Home” messages from our dock friends.  Our extended family.

And to that end, this little thing goes out to Kevin, Debi, Jay, Tina, Pam and Charles – a few of that extended B Dock family.  Thank you for all of your thoughts, prayers, and looking after our boat, worry for us, staying in touch, checking my batteries in the boat (Jay), and watching over Adventure during the hurricane (Debi and Kevin).  We can’t thank you guys enough.  (By the way, I’m probably gonna need a ride to the place to pick up my car Monday… anyone? LOL)

This weekend and week coming up, I will be getting the boat ready for an extended trip.  At this point, we have Abacos and Marsh Harbor in our sights.  JoAnne, more than anyone in the world right now, deserves a break, an island, an island drink, a beach and a vacation.

I’m going to give it to her.